What is the difference between a laser printer and an inkjet printer? A laser printer prints with a toner and an inkjet printer prints with ink. How come my inkjet printer has black stripes?
In most cases, the inkjet printer cartridge is broken and the cartridge needs to be replaced. What does DPI stand for? DPI stands for Dots Per Inch and is the number of ink droplets per inch that end up on the paper when printing. How many cartridges can be placed in the Brother HL? Is the manual of the Brother HL available in English? Yes, the manual of the Brother HL is available in English.
USB 2. Mac OS X Registration roller When the front edge of the paper hit the stopped registration roller and the inclination of the paper is corrected. Registration rear actuator Detect the passage of paper and adjust the starting position for writing on a sheet of paper. When the duplex printing, detect the rear edge of paper and adjust the timing of eject roller 2 switching.
Transfer roller By applying a minus charge to the transfer roller, the toner adhered to the exposure drum is transferred to paper, and feed the paper to the fuser unit. Heat roller and Pressure roller The toner transferred on paper being fused by heat and pressure, and feed the paper to the eject roller 1. Paper eject actuator Detect whether or not paper is ejected from the fuser unit.
Eject roller 1 Feed the paper ejected from the fuser unit to the eject roller 2. Eject roller 2 Eject the paper to the face-down output tray. When the duplex printing, after the paper is fed from the eject roller 2 with the front of sheet printed, the eject roller 2 rotates conversely and feed the paper to the duplex tray.
See the reference page and take the corrective action described for each indication to correct it. But some of errors are necessary to reset the printer by holding down the [Go] button. When entering this state, instruct the end user to turn off the power switch once, and wait a few seconds. Then, turn on the power switch again. However, if the error is not cleared and the service call is appeared, see the reference page to take the corrective action.
Take the proper action by seeing to the reference page. If you can not print, you can use a Maintenance tool to distinguish the type of error. And then the printer goes into the PIT3 mode. If the same problem occurs again, follow each procedure in the order of the number described in the Step column in the tables below. Step Cause Remedy 1 Link arm catching on some position Re-assemble the link arm. Harness connection failure of main Reconnect the harness of the main motor.
Then press the [Go] button. Plate-up gear gear Z19M10 or lift Replace the plate-up gear gear Z19M10 5 gear 46 failure or lift gear If any problem occurs, replace the regist frame ASSY. Step Cause Remedy 1 Paper feeding kit failure Replace the paper feeding kit. If jammed, remove it. Step Cause Remedy Registration front actuator Correct catching of the registration front 1 catching on some position actuator.
Registration rear actuator or paper Correct catching of the registration rear 2 eject actuator catching on some actuator or paper eject actuator. Step Cause Remedy Foreign object around eject roller Remove the foreign object around the eject 1 roller. Step Cause Remedy Foreign object around duplex tray Remove the foreign object around the 1 duplex tray. Step Cause Remedy 1 Fuser unit dirty Clean the entrance of the fuser unit, or clean the pressure roller. Refer to Fig. Step Cause Remedy Foreign object inside fuser unit Remove the foreign object inside of the 1 eject roller.
Step Cause Remedy 1 Fuser unit failure Replace the fuser unit. If the same problem occurs, follow each procedure in the order of the number described in the Step column in the tables below. High temperature and high humidity or low temperature and low humidity conditions can cause this problem.
Off the toner save mode. If remove the used toner cartridge and replace a relatively new used toner cartridge, this case is caused. Step Cause Remedy Dirt on electrodes of the drum unit Clean the electrodes of the drum unit and 1 and printer body printer body.
Unplug the printer from the AC power outlet, and leave the printer for a few minutes. Then, wipe the electrodes above carefully with a dry lint-free cloth. Be careful not to change the shapes of the electrodes. Step Cause Remedy Adjusted value of the laser unit Refer to "2. Registration rear actuator catching Correct catching of the registration rear 2 on some position actuator.
Step Cause Remedy Dirt on the electrodes of the drum Clean the electrodes of the drum unit and 1 unit and the printer body printer body. Scanner harness of the laser unit Reconnect the scanner harness of the 2 connection failure laser unit. Step Cause Remedy Dirt on drum unit and printer body Clean the electrodes of the drum unit and 1 electrodes printer body. Step Cause Remedy 1 Dirt on the fuser unit Replace the fuser unit.
In this case, clean the corona wire. Wipe off the dirt on the exposure drum. Step Cause Remedy 1 Dirt in the paper feed system Wipe dirt off. The printed side must be face down. Clean the contact with a dry cloth. Bend of tray ground spring 1 Correct bending of the tray ground spring. Toner attached on the develop This problem will disappear by printing 3 roller horizontal stripes at If the same problem mm occurs, replace the toner cartridge. Scratch and Dirt on the heat roller Replace the fuser unit.
Bottom surface of Paper tray Paper tray ground terminal Fig. Specify the cause referring to the diameter of the rollers or pitch which appears in the image as shown in the table below The pitch which No.
Try to change to freshly unpacked paper. Step Cause Remedy 1 Laser unit failure Replace the laser unit. Print several sheets of page if the printer has not been used for a long time.
Step Cause Remedy 1 Dirt on the electrodes of the drum Clean the electrodes of the drum unit and unit and the printer body printer body. If the same problem occurs after cleaning, replace the drum unit with a new one. Step Cause Remedy Bend of tray ground spring 1 Correct bending of the tray ground spring. Step Cause Remedy New toner actuator catching on Correct catching of the new toner 1 some position actuator.
For installation details, see the instructions supplied with the lower tray unit. An optional network print server NCp allows your printer to be connected to your network via the parallel interface. You can see how to replace the toner cartridge. You can see how to replace the drum unit. If the LED shows this message, the toner will soon run out. Purchase a new toner cartridge and have it ready before you get a Toner Empty message. Page 75 If the LED shows the following message, the printer has run out of toner or the toner is not evenly distributed inside the cartridge.
To purchase toner cartridges, consult the dealer where you purchased the printer. Page 76 We recommend that you place the drum unit assembly on a piece of disposable paper or cloth in case you accidentally spill or scatter toner. To prevent damage to the printer from static electricity, do not touch the electrodes shown in the illustration. Page 78 Caution Install the toner cartridge immediately after you remove the protective cover.
Do not touch the shaded parts in the illustration to prevent any degradation to the print quality. Install the new toner cartridge into the drum unit until you hear it lock into place. When the toner cartridge is installed correctly, the lock lever is lifted automatically.
Page 79 Re-install the drum unit assembly in the printer. Close the front cover. The printer should be used only in a clean, dust-free environment with adequate ventilation. To prevent damage to the printer from static electricity, do not touch the electrodes shown below. Page 83 Unpack the new drum unit. Caution Wait to unpack a drum unit until immediately before you install it in the printer.
If an unpacked drum unit is subjected to excessive direct sunlight or room light, the unit may be damaged. Make sure that the Drum LED is now off.
Caution We recommend that you clean the printer when you replace the toner cartridge. If printouts are stained with toner, clean the printer interior and drum unit. You can see the instructional movie. You can see how to clean the scanner window. The units listed below should be replaced after printing the following number of pages.
See Chapter 1. Page 89 Turn the power switch off, wait a few seconds and then turn it on again. If the error occurs again, consult your dealer. Page 90 The printer will report problems by printing an error message as defined in the following table. Take the corrective actions for the error message. Page 91 First, ensure that you are using paper that meets Brother recommended paper specifications. See Problem The printer does not load paper. The printer does not load paper from the manual feed slot.
The printer will not load envelopes. A paper jam has occurred. When you open the front or rear cover of the printer, never touch the shaded parts shown in the following diagram. Clear the jammed paper referring to the following description.
Page 93 Always remove all paper from the paper cassette and straighten the stack when new paper is added. This helps prevent multiple sheets of paper from feeding through the printer at one time and reduces paper jams. Pull the paper cassette completely out of the printer. Pull the jammed paper up and out of the printer. If you cannot remove the drum unit assembly easily at this time, do not use additional force. Instead, pull the edge of the jammed paper from the paper cassette.
Print a few copies of the test page until the scattering of toner stops. Page 97 Check that the USB interface cable is connected correctly.
Make sure that the supplied Macintosh printer driver is installed in the System Folder and that it is selected with Chooser. Page 98 Chapter 5. See Chapter 5. Do you have a question about the Brother HL or do you need help? Ask your question here. Provide a clear and comprehensive description of the issue and your question. The more detail you provide for your issue and question, the easier it will be for other Brother HL owners to properly answer your question. View the manual for the Brother HL here, for free.
This manual comes under the category Printers and has been rated by 1 people with an average of a 6. This manual is available in the following languages: English. Below, you will find the most frequently asked questions about the Brother HL Is your question not listed?
You must set up the hardware and install the dr iver before you can use the ma chine.
0コメント